چگونه آباکوس را ?اد بگ?ر?م؟

چگونه آباکوس را ?اد بگ?ر?م؟ ا?ن روند نما?? است که شرکت سازنده نرم افزار معرف? کرده است.

The following reading list is recommended as a 'road map' to learning how to use the Abaqus software suite. It has been adapted from thetraining program that all Abaqus Customer Support Engineers must complete. For maximum benefit, it is highly recommended that you complete all included examples and workshop problems. The documentation references refer to Version 6.10.

Manual	Additional reading and comments
Getting Started with Abaqus	This gives a very good overview to Abaqus/Standard and Abaqus/Explicit using Abaqus/CAE. It also teaches the basics of Abaqus/Viewer. On-line Keywords versions are also available for Abaqus/Standard and Abaqus/Explicit.
Chapters 1 through 6 of the Abaqus/CAE User's Manual	These are the "Getting Started" sections for Abaqus/CAE and Abaqus/Viewer and will allow you to gain basic proficiency.
Abaqus Analysis User's Manual	Sections 1.1--1.3, Chapters 2 and 3, Section 4.1 and the beginning of section 4.2 (until you reach the output variable identifiers), Sections 4.3, 5.1.1, 6.1, 6.2.1, 6.2.2, 6.2.5, 6.3.2, 6.3.3, Chapters 7, 18, 30, and 31. Sections 1-4 discuss the aspects of defining and running an analysis in Abaqus, while the remaining sections provide an overview of the different type of simulations that can be done.

The remaining documentation items are Lecture Notes used in the seminars offered by SIMULIA. They discuss the finer points of more advanced topics and can be read as needed. The list shown below is not complete, but is representative of the most common usage of Abaqus. Please see the Seminar Descriptions in the Training section of the SIMULIA homepage to see the complete list of the latest lecture notes available.

The relevant sections of the Abaqus Analysis User's manual should be read once you have completed a specific set of lecture notes. Some example or benchmark problems are referred to with each set of lecture notes. The list of example or benchmark problems is not comprehensive. There are many other example or benchmark problems that may be relevant and useful for you to read.

Abaqus/CAE: Geometry Import and Meshing	Read the corresponding sections of the Abaqus/CAE User's Manual and also consult the web-based Geometry Import and Repair Guide.
Flexible Multibody Dynamics with Abaqus	Also read Chapter 27 of the Abaqus Analysis User's Manual.
Introduction to Abaqus Scripting	Also consult the Abaqus Scripting Manual and the Abaqus Scripting Command Reference.
Structural-Acoustic Analysis with Abaqus	Also read Section 6.10 of the Abaqus Analysis User's Manual.
Tire Modeling using Abaqus	Also read Section 6.4 of the Abaqus Analysis User's Manual.
Automotive Powertrain Assembly Analysis with Abaqus	Advanced notes based on a number of the other lecture notes as well as significant original material specific to the powertrain industry.
Fracture Mechanics with Abaqus	Also read sections 10.6 and 11.4 of the Abaqus Analysis User's Manual.
Analysis of Geotechnical Problems with Abaqus	Also read Sections 6.8, 19.3, 19.4 of the Abaqus Analysis User's Manual.

Lecture Notes	Additional reading and comments
Element Selection in Abaqus/Standard	Also read chapter 24 on Elements in the Abaqus Analysis User's Manual. Benchmark Problem: 2.1.2 Geometrically nonlinear analysis of a cantilever beam
Metal Inelasticity in Abaqus	These are basic lectures on metal plasticity. Example Problems:  1.1.7 Notched beam under cyclic loading Benchmark Problems:  3.2.2 Test of ORNL plasticity theory under biaxial loading 3.2.8 Simple proportional and nonproportional cyclic tests 3.2.15 Creep of a thick cylinder under internal pressure 3.2.17 Stretching of a plate with a hole
Contact In Abaqus/Standard	Also read Sections 2.3, and Chapters 32 to 35 of the Abaqus Analysis User's Manual. Example Problems: 1.1.1 "Axisymmetric analysis of bolted pipe flange connections" 1.1.18 "Self-contact in rubber/foam components: rubber gasket" 1.1.20 "Axisymmetric analysis of a threaded connection" 1.3.1 "Upsetting of a cylindrical billet" 1.3.3 "Stretching of a thin sheet with a hemispherical punch"
Obtaining a Converged Solution with Abaqus	Uses information from many of the lecture notes and manuals. Example Problems: 1.1.2 Elastic-plastic collapse of a thin-walled elbow under in-plane bending and internal pressure 1.3.17 Unstable static problem: thermal forming of a metal sheet Benchmark Problems: 1.1.6 Snap-through of a shallow, cylindrical roof under a point load 1.1.7 Pressurized rubber disc 1.1.10 Concrete slump test
Abaqus/Explicit: Advanced Topics	Also read Sections 9.2.2, 12.2.1, 22.2, 32.4, and 32.5 of the Abaqus Analysis User's Manual. Example Problems: 1.3.6 Rolling of thick plates 1.3.9 Forging with sinusoidal dies 2.1.10 Crimp forming with general contact 2.1.14 Water sloshing in a baffled tank Benchmark Problems: 1.3.9 Pipe whip simulation
Buckling, Postbuckling and Collapse Analysis with Abaqus	Also read sections 6.2.3, 6.2.4, and 11.3 of the Abaqus Analysis User's Manual. Example Problems: 1.2.1 Snap-through buckling analysis of circular arches 1.2.6 Buckling of an imperfection-sensitive cylindrical shell
Heat Transfer/Thermal Stress Analysis with Abaqus	Also read section 6.5 and relevant parts of Chapter 25 of the Abaqus Analysis User's Manual. Example Problems: 5.1.1 Thermal-stress analysis of a disc brake 5.1.3 Exhaust manifold assemblage 5.1.4 Coolant manifold cover gasketed joint 7.2.1 Thermal-electrical modeling of an automotive fuse Benchmark Problems: 1.6.4 Quenching of an infinite plate
Modeling Rubber and Viscoelasticity with Abaqus	Also read sections 19.5--19.8 of the Abaqus Analysis User's Manual. Example Problems: 1.1.4 Indentation of an elastomeric foam specimen with a hemispherical punch 1.1.17 Self-contact in rubber/foam components: jounce bumper 3.1.1 Symmetric results transfer for a static tire analysis  Benchmark Problems: 3.1.2 Transient thermal loading of a viscoelastic slab
Analysis of Composite Materials with Abaqus	Also read sections 19.2.3, and 21.3 25.1.1, 25.1.4, and 26.6 of the Abaqus Analysis User's Manual. Example Problems: 1.1.14 Damage and failure of a laminated composite plate 1.2.2 Laminated composite shells: buckling of a cylindrical panel with a circular hole Benchmark Problems: 1.1.3 Composite shells in cylindrical bending
Linear and Nonlinear Dynamics with Abaqus	Also read section 6.3 of the Abaqus Analysis User's Manual. Example Problems: 2.1.2 Detroit Edison pipe whip experiment 2.1.5 Tennis racket and ball 3.1.3 Subspace-based steady-state dynamic tire analysis 9.1.6 Coupled acoustic-structural analysis of a pick-up truck Benchmark Problems: 1.3.2 Double cantilever elastic beam under point load 1.4.12 Double cantilever subjected to multiple base motions
Metal Forming with Abaqus	Also read sections 6.3.3, 9.2.2 and 12.2 of the Abaqus Analysis User's Manual. Example Problems: 1.3.2 Superplastic forming of a rectangular box 1.3.7 Axisymmetric forming of a circular cup 1.5.1 Springback of two-dimensional draw bending
Substructures and Submodeling with Abaqus	Also read sections 10.1, and 10.2 of the Abaqus Analysis User's Manual. Example Problems: 1.4.2 Contour integrals for a conical crack in a linear elastic infinite half space 2.2.1 Analysis of a rotating fan using substructures and cyclic symmetry
Writing User Subroutines with Abaqus	Also read the Abaqus User Subroutines Reference Manual. Example Problems: 1.1.15 Analysis of an automotive boot seal Verification Problems: 2.2.8 Transient internal pressure loading of a viscoelastic cylinder